Due to the lack of measurements in many regions, wave characteristics are estimated using different methods. Wave climate hindcasting/forecasting is mostly conducted by numerical models or empirical methods. Until now, different empirical methods have been developed for wave hindcasting. However, with the development of high speed processors, several sophisticated numerical models have been developed for wave prediction. These models are mostly phase-averaged spectral wave models developed in three generations. In the last two decades, third generation wave models have been used widely in academic and practical projects. In this regard, Port and Maritime Organization has produced his own model, PMO DYNAMIC. This model has been developed as a part of first three phases of Monitoring and Modeling of Study of Iranian Coasts project. PMO DYNAMIC package is a software available for engineering purposes. It has several modules that have been developed for different objectives. Wave model is the module which is used for the generation and transformation of wind waves in coastal areas. In this paper, in order to test the PMO DYNAMIC model capabilities, it has been applied for the prediction of wave parameters in Bushehr Bay and the results have been compared with MIKE21 SW model and measured data.

A mathematical model based on d-q axis theory and DYNAMIC PERFORMANCE characteristic of brushless resolvers is discussed in this paper. The impact of rotor eccentricity on the accuracy of position in precise applications is investigated. In particular, the model takes the stator currents of brushless resolver into account. The proposed model is used to compute the DYNAMIC and steady state equivalent circuit of resolvers. Finally, simulation results are presented. The validity and usefulness of the proposed method are thoroughly verified with experiments.

Background: In intertrochanteric fractures، DYNAMIC hip screw (DHS) is the most frequently used tool، but several studies did not give good results for this device in reverse-oblique and transverse fractures. Current study aimed to compare fixation results of reverse-oblique intertrochanteric and short-segment subtrochanteric fractures using DYNAMIC condylar screw (DCS) and DHS in patients referred to Alzahra and Kashani Hospitals in Isfahan, Iran.Methods: In a cross-sectional study، medical files of the patients referred to emergency units of the two hospitals who were diagnosed with intertrochanteric or subtrochanteric fractures and underwent DHS or DCS surgery more than 6 months before were assessed; they were invited for follow-up visit and examination. Written consent forms were taken from all the patients upon their entry; and they were examined in terms of complications including nonunion and failure of device and level of fracture improvement. These cases were evaluated by simple radiography ,too. Results obtained from examination of patients in addition to demographic information were recorded in the data collection form for each patient.Findings: Perfect union was observed in 14 (of 25) patients in DHS group and 21 (of 25) patients in DCS group (56% vs. 84%) six months after the surgery. Bone union was significantly better in DCS group (P=0.031). In addition, six months after the surgery, the devices used in 14 people in DHS group and 24 people in DCS group were fixed and the difference between the two groups was significant (P=0.001). 14 and 24 patients had total recovery in DHS and DCS groups، respectively (20% vs. 44%) with a significant difference (P=0.020).Conclusion: Considering obtained results, it can be concluded that using DCS is recommended over DHS due to severity of pain, bone union and fixation of the device.

One of the issues of reliable PERFORMANCE in the power grid is the existence of electromechanical oscillations between interconnected generators. The number of generators participating in each electromechanical oscillation mode and the frequency oscillation depends on the structure and function of the power grid. In this paper, to improve the transient nature of the network and damping electromechanical fluctuations, a decentralized robust adaptive control method based on DYNAMIC programming has been used to design a stabilizing power system and a complementary static var compensator (SVC) controller. By applying a single line to ground fault in the network, the robustness of the designed control systems is demonstrated. Also, the simulation results of the method used in this paper are compared with controllers whose parameters are adjusted using the PSO algorithm. The simulation results show the superiority of the decentralized robust adaptive control method based on DYNAMIC programming for the stabilizing design of the power system and the complementary SVC controller. The PERFORMANCE of the control method is tested using the IEEE 16-machine, 68-bus, 5-area is verified with time domain simulation.